PROACTIVE ENVIRONMENTAL PRODUCTS®
Electra²® 12 Volt Peristaltic Pump
With Double Pump Head
Designed for the Field Technician in mind!
The Electra²® peristaltic pump with double pump head is lightweight and compact. To use, simply attach an external power source such as a 12-volt deep cycle battery to energize the pump. A high-performance motor consumes only 3 amps at maximum draw making Electra²® peristaltic pump with double pump head extremely efficient. The rugged Pelican™ 1300 case enclosure is made of impact and corrosion resistant ABS plastic to withstand demanding work conditions. Incorporating the most accurate and precise variable speed controller for consistent flow rates will ensure the technician reliable and consistent sample integrity.
Constant Voltage Boosting Technology (CVBT)
Proprietary system that boosts a "low voltage battery" to an amazing range of 13.5-14.5 volts when the dial is turned up 100%. That means faster water discharge rates and more consistent pumping rates. Which in turn makes your next groundwater field sampling event a profit center!
Push Button Back Flushing
Supplied with a push button reversible flow feature for back-flushing.
Precise Flow Technology:
Obtain precise sampling by utilizing
simple dial-in technology using the
rheostat on the side of the Electra²®
pump. Turn up the dial for faster
pumping or turn down the dial to
achieve the perfect low flow sample
as low as 40 ml per minute, in
conjunction with the low flow control valve.
Masterflex Easyload™ 2 pump head design
Super strong - Lightweight Pelican™ 1300 case
The Electra²® peristaltic pump utilizes a Pelican™ 1300 case that lends hand to durability and weighs only 10 pounds. The rugged Pelican™ case enclosure is made of impact and corrosion resistant ABS plastic to withstand demanding work conditions.
Low Voltage Disconnect Warning (LVD)
If the LVD (Low Voltage Disconnect) light appears red (located next to the low flow control dial), the pump will shut off automatically which indicates the battery output voltage is 10.75 volts or lower. In short, the battery is reaching a “critical low level” so stop using the unit immediately and please recharge your battery within 24 hours.
Two fuses are located inside the 10-foot cigarette DC male power plug cord, please make sure you check these two fuses before checking the internal fuse. Please replace with another 30 AMP glass fuse if blown.
If the Internal Fuse “blows”, it will automatically shut off the pump. This only happens if you should accidentally “reverse polarity” the pump clamps to the battery. In addition, incorporated into the mother board is an internal 7.5 AMP fuse. The fuse is simple to replace. Please open panel to replace the 7.5 AMP fuse. It is located on the master board. Simply unplug the 10-foot power plug from the battery and then cut the cable ties that lock the case closed. Once gaining access to the fuse compartment you can now replace fuse with a new 7.5 AMP fuse. Now, hook up the power plug to the battery terminals again. Turn on the power and the pump is ready to use.
Push Button Back
Low Flow Control Dial
Super fast tubing load times; No more stretching and jamming silicon tubing through the pump head and defiantly no more fiddling with screws to gain access to the pump head. Located on case exterior allowing the user to easily shut the enclosure.
Pumps up to 5 liters per minute or as low as 40 mL per minute*
Suction lift up to 26 feet from sea level
Supplied with two pump heads
10 feet of DC battery clamps to hook up for super long sampling events
Product Dimensions: Depth 9 3/4" x Width 15" x Height 6 3/4"
Weight of Product: 10 Pounds
Please Note: The proper silicone tubing into the Masterflex Easy-Load 2 Pump Head.
Please use Masterflex or tubing comparable to:
→ MF# LS 15: 3/16"ID X 3/8" OD
→ MF# LS 24: 1/4" ID X 7/16" OD
→ MF# LS 36: 3/8" ID X 5/8" OD
Masterflex Easyload™ 2 pump head is a registered trademark of Thermo Fisher Scientific
* Test conducted with 3 feet of size 36 Masterflex™ tubing
What is included in the box: